Реклама на сайте English version  DatasheetsDatasheets

KAZUS.RU - Электронный портал. Принципиальные схемы, Datasheets, Форум по электронике

Новости электроники Новости Литература, электронные книги Литература Документация, даташиты Документация Поиск даташитов (datasheets)Поиск PDF
  От производителей
Новости поставщиков
В мире электроники

  Сборник статей
Электронные книги
FAQ по электронике

  Datasheets
Поиск SMD
Он-лайн справочник

Принципиальные схемы Схемы Каталоги программ, сайтов Каталоги Общение, форум Общение Ваш аккаунтАккаунт
  Каталог схем
Избранные схемы
FAQ по электронике
  Программы
Каталог сайтов
Производители электроники
  Форумы по электронике
Удаленная работа
Помощь проекту

Микроконтроллеры, АЦП, память и т.д Темы касающиеся микроконтроллеров разных производителей, памяти, АЦП/ЦАП, периферийных модулей...

 
Опции темы
Непрочитано 02.06.2019, 12:46  
Alex_golubev
Прописка
 
Регистрация: 07.02.2016
Сообщений: 137
Сказал спасибо: 4
Сказали Спасибо 1 раз в 1 сообщении
Alex_golubev на пути к лучшему
По умолчанию imx287 ошибка загрузки линукса

Привет.
Сразу опишу что делал и как дошел до ошибки.
Создал рабочею директорию и клонировал buildroot.
mkdir work
cd work
git clone https://github.com/buildroot/buildroot

После собрал.
cd buildroot
make freescale_imx28evk_defconfig
make

Записал на sd-карту.
sudo dd if=output/images/sdcard.img of=/dev/sdb bs=4M

Запустил.
Получил ошибку
Нажмите, чтобы открыть спойлер

HTLLCLLC

U-Boot 2018.05 (May 13 2019 - 20:18:27 +0700)

CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
SPI: ready
DRAM: 128 MiB
No arch specific invalidate_icache_all available!
NAND: 256 MiB
MMC: MXS MMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

Failed (-5)
Video: MXSFB: 'videomode' variable not set!
In: serial
Out: serial
Err: serial
Net: FEC0 [PRIME], FEC1
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Unable to read file boot.scr **
4506320 bytes read in 1333 ms (3.2 MiB/s)
Booting from mmc ...
22340 bytes read in 31 ms (703.1 KiB/s)
Kernel image @ 0x42000000 [ 0x000000 - 0x44c2d0 ]
## Flattened Device Tree blob at 41000000
Booting using the fdt blob at 0x41000000
Loading Device Tree to 47b17000, end 47b1f743 ... OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.17.8 (alexey@debian) (gcc version 7.4.0 (Buildroot 2019.05-rc1-00022-g653bf93837)) #1 Mon May 13 20:20:07 +07 2019
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: Freescale i.MX28 Evaluation Kit
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x474 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyAMA0,115200 root=/dev/mmcblk0p3 rw rootwait
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113240K/131072K available (6064K kernel code, 555K rwdata, 2008K rodata, 300K init, 7442K bss, 17832K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6066 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) ( 300 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 556 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7443 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Running RCU self tests
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: mxs_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000032] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.002268] Console: colour dummy device 80x30
[ 0.002431] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.002498] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.002552] ... MAX_LOCK_DEPTH: 48
[ 0.002604] ... MAX_LOCKDEP_KEYS: 8191
[ 0.002653] ... CLASSHASH_SIZE: 4096
[ 0.002703] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.002753] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.002803] ... CHAINHASH_SIZE: 32768
[ 0.002854] memory used by lock dependency info: 4655 kB
[ 0.002904] per task-struct memory footprint: 1536 bytes
[ 0.003104] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[ 0.071444] pid_max: default: 32768 minimum: 301
[ 0.072578] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.072688] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081135] CPU: Testing write buffer coherency: ok
[ 0.090281] Setting up static identity map for 0x40008400 - 0x40008458
[ 0.103357] devtmpfs: initialized
[ 0.165055] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.165303] futex hash table entries: 256 (order: 1, 11264 bytes)
[ 0.166948] pinctrl core: initialized pinctrl subsystem
[ 0.181233] NET: Registered protocol family 16
[ 0.184234] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.389720] Serial: AMBA PL011 UART driver
[ 0.393358] 80074000.serial: ttyAMA0 at MMIO 0x80074000 (irq = 236, base_baud = 0) is a PL011 rev2
[ 0.715045] console [ttyAMA0] enabled
[ 0.802110] mxs-dma 80004000.dma-apbh: initialized
[ 0.820126] mxs-dma 80024000.dma-apbx: initialized
[ 0.847131] SCSI subsystem initialized
[ 0.854109] usbcore: registered new interface driver usbfs
[ 0.860383] usbcore: registered new interface driver hub
[ 0.866692] usbcore: registered new device driver usb
[ 0.881533] pps_core: LinuxPPS API ver. 1 registered
[ 0.886802] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.896210] PTP clock support registered
[ 0.903170] Advanced Linux Sound Architecture Driver Initialized.
[ 0.917667] clocksource: Switched to clocksource mxs_timer
[ 1.575246] NET: Registered protocol family 2
[ 1.584911] tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 5120 bytes)
[ 1.593098] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.600461] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[ 1.608070] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.615633] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.622424] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.630647] NET: Registered protocol family 1
[ 1.641515] RPC: Registered named UNIX socket transport module.
[ 1.648027] RPC: Registered udp transport module.
[ 1.652821] RPC: Registered tcp transport module.
[ 1.657806] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.679156] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 1.769294] NFS: Registering the id_resolver key type
[ 1.775504] Key type id_resolver registered
[ 1.780272] Key type id_legacy registered
[ 1.784864] jffs2: version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
[ 1.816384] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 24
[ 1.824400] io scheduler noop registered (default)
[ 1.829534] io scheduler mq-deadline registered
[ 1.834162] io scheduler kyber registered
[ 1.848166] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 1.906739] Console: switching to colour frame buffer device 100x30
[ 1.933880] mxsfb 80030000.lcdif: initialized
[ 1.945627] 8006a000.serial: ttyAPP0 at MMIO 0x8006a000 (irq = 234, base_baud = 1500000) is a 8006a000.serial
[ 1.958143] mxs-auart 8006a000.serial: Found APPUART 3.1.0
[ 1.966116] 80070000.serial: ttyAPP3 at MMIO 0x80070000 (irq = 235, base_baud = 1500000) is a 80070000.serial
[ 1.978757] mxs-auart 80070000.serial: Found APPUART 3.1.0
[ 2.029812] random: fast init done
[ 2.070123] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 2.076578] nand: Micron MT29F2G08ABAEAWP
[ 2.080888] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.096923] Scanning device for bad blocks
[ 3.361197] gpmi-nand 8000c000.gpmi-nand: driver registered.
[ 3.398391] m25p80 spi1.0: unrecognized JEDEC id bytes: ff, ff, ff
[ 3.410138] libphy: Fixed MDIO Bus: probed
[ 3.566692] libphy: fec_enet_mii_bus: probed
[ 3.577215] fec 800f4000.ethernet: 800f4000.ethernet supply phy not found, using dummy regulator
[ 3.594548] usbcore: registered new interface driver asix
[ 3.600697] usbcore: registered new interface driver ax88179_178a
[ 3.607240] usbcore: registered new interface driver cdc_ether
[ 3.613914] usbcore: registered new interface driver smsc95xx
[ 3.620420] usbcore: registered new interface driver net1080
[ 3.626526] usbcore: registered new interface driver cdc_subset
[ 3.633131] usbcore: registered new interface driver zaurus
[ 3.639581] usbcore: registered new interface driver cdc_ncm
[ 3.645341] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.652689] usbcore: registered new interface driver usb-storage
[ 3.690017] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 3.695981] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.727977] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.748559] hub 1-0:1.0: USB hub found
[ 3.753477] hub 1-0:1.0: 1 port detected
[ 3.773581] input: mxs-lradc-ts as /devices/soc0/80000000.apb/80040000.apbx/80050000.lradc/mxs-lradc-ts/input/input0
[ 3.794488] stmp3xxx-rtc 80056000.rtc: rtc core: registered 80056000.rtc as rtc0
[ 3.804062] i2c /dev entries driver
[ 3.818414] stmp3xxx_rtc_wdt stmp3xxx_rtc_wdt: initialized watchdog with heartbeat 19s
[ 3.832872] mxs-mmc 80010000.ssp: Got WP GPIO
[ 3.870302] mxs-mmc 80010000.ssp: initialized
[ 3.897334] mxs-dcp 80028000.dcp: Failed to register sha1 hash!
[ 3.906933] mxs-dcp: probe of 80028000.dcp failed with error -22
[ 3.920738] usbcore: registered new interface driver usbhid
[ 3.926401] usbhid: USB HID core driver
[ 3.946834] mmc0: new high speed SDHC card at address aaaa
[ 3.972649] mmcblk0: mmc0:aaaa SL16G 14.8 GiB (ro)
[ 4.013409] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[ 4.026085] mmcblk0: p1 p2 p3
[ 4.030852] NET: Registered protocol family 17
[ 4.036616] Key type dns_resolver registered
[ 4.065853] registered taskstats version 1
[ 4.153987] sgtl5000 0-000a: Error reading chip id -6
[ 4.165340] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[ 4.176079] stmp3xxx-rtc 80056000.rtc: setting system clock to 1970-01-01 00:14:10 UTC (850)
[ 4.186265] usb0_vbus: disabling
[ 4.190536] can-3v3: disabling
[ 4.193703] ALSA device list:
[ 4.196739] No soundcards found.
[ 4.205365] uart-pl011 80074000.serial: no DMA platform data
[ 4.214481] VFS: Cannot open root device "mmcblk0p3" or unknown-block(179,3): error -30
[ 4.222873] Please append a correct "root=" boot option; here are the available partitions:
[ 4.231696] 1f00 262144 mtdblock0
[ 4.231740] (driver?)
[ 4.238636] b300 15558144 mmcblk0
[ 4.238680] driver: mmcblk
[ 4.245608] b301 16384 mmcblk0p1 00000000-01
[ 4.245642]
[ 4.252774] b302 16384 mmcblk0p2 00000000-02
[ 4.252812]
[ 4.259947] b303 61440 mmcblk0p3 00000000-03
[ 4.259988]
[ 4.266913] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,3)
[ 4.275426] CPU: 0 PID: 1 Comm: swapper Not tainted 4.17.8 #1
[ 4.281228] Hardware name: Freescale MXS (Device Tree)
[ 4.286493] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[ 4.294360] [] (show_stack) from [] (panic+0xcc/0x25
[ 4.301355] [] (panic) from [] (mount_block_root+0x1bc/0x2c0)
[ 4.308942] [] (mount_block_root) from [] (mount_root+0x110/0x154)
[ 4.316954] [] (mount_root) from [] (prepare_namespace+0x128/0x18
[ 4.325054] [] (prepare_namespace) from [] (kernel_init_freeable+0x310/0x36c)
[ 4.334035] [] (kernel_init_freeable) from [] (kernel_init+0x8/0xf0)
[ 4.342220] [] (kernel_init) from [] (ret_from_fork+0x14/0x24)
[ 4.349852] Exception stack(0xc7483fb0 to 0xc7483ff
[ 4.354974] 3fa0: 00000000 00000000 00000000 00000000
[ 4.363222] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 4.371464] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 4.378190] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,3) ]---
[ 67.597805] random: crng init done


Решение оказалось:
Нажмите, чтобы открыть спойлер

ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
//wp-gpios = <&gpio2 12 0>; // нужно убрать
vmmc-supply = <®_vddio_sd0>;
status = "okay";
};


Пересобрал.
cd /home/alexey/work/buildroot
make linux-rebuild
make
Запрограммировал SD-карту. Все тем же dd.
И получил:
Нажмите, чтобы открыть спойлер

Код:
<0><0>HTLLCLLC

U-Boot 2018.05 (May 15 2019 - 08:52:49 +0700)

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SD/MMC #0, 3V3
SPI:   ready
DRAM:  128 MiB
No arch specific invalidate_icache_all available!
NAND:  256 MiB
MMC:   MXS MMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

Failed (-5)
Video: MXSFB: 'videomode' variable not set!
In:    serial
Out:   serial
Err:   serial
Net:   FEC0 [PRIME], FEC1
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
** Unable to read file boot.scr **
4506312 bytes read in 1333 ms (3.2 MiB/s)
Booting from mmc ...
22316 bytes read in 31 ms (702.1 KiB/s)
Kernel image @ 0x42000000 [ 0x000000 - 0x44c2c8 ]
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 47b17000, end 47b1f72b ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.17.8 (alexey@alexey) (gcc version 7.4.0 (Buildroot 2019.05-rc1-00043-g47840289bf)) #1 Wed May 15 08:54:19 +07 2019
[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX28 Evaluation Kit
[    0.000000] Memory policy: Data cache writeback
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x474 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyAMA0,115200 root=/dev/mmcblk0p3 rw rootwait
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113240K/131072K available (6064K kernel code, 555K rwdata, 2008K rodata, 300K init, 7442K bss, 17832K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (6066 kB)
[    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   ( 300 kB)
[    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 556 kB)
[    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   (7443 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Running RCU self tests
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: mxs_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000032] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.002269] Console: colour dummy device 80x30
[    0.002430] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.002497] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.002551] ... MAX_LOCK_DEPTH:          48
[    0.002603] ... MAX_LOCKDEP_KEYS:        8191
[    0.002652] ... CLASSHASH_SIZE:          4096
[    0.002702] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.002753] ... MAX_LOCKDEP_CHAINS:      65536
[    0.002802] ... CHAINHASH_SIZE:          32768
[    0.002853]  memory used by lock dependency info: 4655 kB
[    0.002903]  per task-struct memory footprint: 1536 bytes
[    0.003102] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[    0.071448] pid_max: default: 32768 minimum: 301
[    0.072579] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.072689] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.081138] CPU: Testing write buffer coherency: ok
[    0.090278] Setting up static identity map for 0x40008400 - 0x40008458
[    0.103344] devtmpfs: initialized
[    0.165096] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.165346] futex hash table entries: 256 (order: 1, 11264 bytes)
[    0.167003] pinctrl core: initialized pinctrl subsystem
[    0.181270] NET: Registered protocol family 16
[    0.184276] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.389524] Serial: AMBA PL011 UART driver
[    0.393133] 80074000.serial: ttyAMA0 at MMIO 0x80074000 (irq = 236, base_baud = 0) is a PL011 rev2
[    0.714817] console [ttyAMA0] enabled
[    0.801795] mxs-dma 80004000.dma-apbh: initialized
[    0.819819] mxs-dma 80024000.dma-apbx: initialized
[    0.846840] SCSI subsystem initialized
[    0.853812] usbcore: registered new interface driver usbfs
[    0.860095] usbcore: registered new interface driver hub
[    0.866404] usbcore: registered new device driver usb
[    0.881253] pps_core: LinuxPPS API ver. 1 registered
[    0.886521] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.895936] PTP clock support registered
[    0.902908] Advanced Linux Sound Architecture Driver Initialized.
[    0.917432] clocksource: Switched to clocksource mxs_timer
[    1.575134] NET: Registered protocol family 2
[    1.584781] tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 5120 bytes)
[    1.592966] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.600326] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    1.607941] TCP: Hash tables configured (established 1024 bind 1024)
[    1.615499] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.622285] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.630503] NET: Registered protocol family 1
[    1.641416] RPC: Registered named UNIX socket transport module.
[    1.647917] RPC: Registered udp transport module.
[    1.652715] RPC: Registered tcp transport module.
[    1.657694] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.678996] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.768982] NFS: Registering the id_resolver key type
[    1.775188] Key type id_resolver registered
[    1.779953] Key type id_legacy registered
[    1.784552] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.816105] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.824115] io scheduler noop registered (default)
[    1.829242] io scheduler mq-deadline registered
[    1.833867] io scheduler kyber registered
[    1.847901] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    1.906519] Console: switching to colour frame buffer device 100x30
[    1.933661] mxsfb 80030000.lcdif: initialized
[    1.945383] 8006a000.serial: ttyAPP0 at MMIO 0x8006a000 (irq = 234, base_baud = 1500000) is a 8006a000.serial
[    1.957873] mxs-auart 8006a000.serial: Found APPUART 3.1.0
[    1.965897] 80070000.serial: ttyAPP3 at MMIO 0x80070000 (irq = 235, base_baud = 1500000) is a 80070000.serial
[    1.978524] mxs-auart 80070000.serial: Found APPUART 3.1.0
[    2.029590] random: fast init done
[    2.070753] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    2.077206] nand: Micron MT29F2G08ABAEAWP
[    2.081518] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.097791] Scanning device for bad blocks
[    3.359499] gpmi-nand 8000c000.gpmi-nand: driver registered.
[    3.398153] m25p80 spi1.0: unrecognized JEDEC id bytes: ff, ff, ff
[    3.409902] libphy: Fixed MDIO Bus: probed
[    3.566642] libphy: fec_enet_mii_bus: probed
[    3.577149] fec 800f4000.ethernet: 800f4000.ethernet supply phy not found, using dummy regulator
[    3.594466] usbcore: registered new interface driver asix
[    3.600607] usbcore: registered new interface driver ax88179_178a
[    3.607152] usbcore: registered new interface driver cdc_ether
[    3.613820] usbcore: registered new interface driver smsc95xx
[    3.620293] usbcore: registered new interface driver net1080
[    3.626431] usbcore: registered new interface driver cdc_subset
[    3.633033] usbcore: registered new interface driver zaurus
[    3.639474] usbcore: registered new interface driver cdc_ncm
[    3.645235] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.652581] usbcore: registered new interface driver usb-storage
[    3.690096] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    3.696056] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    3.727749] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    3.748361] hub 1-0:1.0: USB hub found
[    3.753288] hub 1-0:1.0: 1 port detected
[    3.773427] input: mxs-lradc-ts as /devices/soc0/80000000.apb/80040000.apbx/80050000.lradc/mxs-lradc-ts/input/input0
[    3.794275] stmp3xxx-rtc 80056000.rtc: rtc core: registered 80056000.rtc as rtc0
[    3.803857] i2c /dev entries driver
[    3.818182] stmp3xxx_rtc_wdt stmp3xxx_rtc_wdt: initialized watchdog with heartbeat 19s
[    3.863135] mxs-mmc 80010000.ssp: initialized
[    3.892303] mxs-dcp 80028000.dcp: Failed to register sha1 hash!
[    3.901989] mxs-dcp: probe of 80028000.dcp failed with error -22
[    3.915649] usbcore: registered new interface driver usbhid
[    3.921562] usbhid: USB HID core driver
[    3.938083] mmc0: host does not support reading read-only switch, assuming write-enable
[    3.958642] mmc0: new high speed SDHC card at address aaaa
[    3.982850] mmcblk0: mmc0:aaaa SL16G 14.8 GiB 
[    4.013573] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[    4.029487]  mmcblk0: p1 p2 p3
[    4.036516] NET: Registered protocol family 17
[    4.046407] Key type dns_resolver registered
[    4.070013] registered taskstats version 1
[    4.157268] sgtl5000 0-000a: Error reading chip id -6
[    4.168888] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[    4.179336] stmp3xxx-rtc 80056000.rtc: setting system clock to 1970-01-01 00:01:51 UTC (111)
[    4.189683] usb0_vbus: disabling
[    4.193375] can-3v3: disabling
[    4.196526] ALSA device list:
[    4.199813]   No soundcards found.
[    4.208503] uart-pl011 80074000.serial: no DMA platform data
[    4.228450] EXT4-fs (mmcblk0p3): mounting ext2 file system using the ext4 subsystem
[    4.272326] EXT4-fs (mmcblk0p3): warning: mounting unchecked fs, running e2fsck is recommended
[    4.290388] EXT4-fs (mmcblk0p3): mounted filesystem without journal. Opts: (null)
[    4.298609] VFS: Mounted root (ext2 filesystem) on device 179:3.
[    4.340858] devtmpfs: mounted
[    4.346407] Freeing unused kernel memory: 300K
[    4.351194] This architecture does not have kernel memory protection.
[    4.596637] EXT4-fs (mmcblk0p3): re-mounted. Opts: block_validity,barrier,user_xattr
Starting syslogd: OK
Starting klogd: OK
Initializing random number generator... [    5.244356] random: dd: uninitialized urandom read (512 bytes read)
done.
Starting network: OK


Welcome to Buildroot

buildroot login:

Загрузил тулчейн
https://releases.linaro.org/components/ ... abi.tar.xz
распаковал его.
Далее в buildroot'е:
make menuconfig, ставим
Нажмите, чтобы открыть спойлер

Код:
Toolchain  --->
    Toolchain type (External toolchain)  --->
    Toolchain (Custom toolchain)  --->
    Toolchain origin (Pre-installed toolchain)  --->
    (Путь к распакованному тулчейну) Toolchain path
    ($(ARCH)-linux-gnueabi) Toolchain prefix
    External toolchain gcc version (7.x)  --->
    External toolchain kernel headers series (4.10.x)  --->
    External toolchain C library (glibc/eglibc)  --->


make clean
make

1. Клонируем репозиторий ядра нужной версии (в директории ~/work):
git clone git://git.kernel.org/pub/scm/linux/kern ... /linux.git --branch=v4.19 --depth=1

2. Для удобства создадим переменную с путем и префиксом к компилятору:
export ARMCC_GNUEABI7=/home/<что-то еще>/gcc-linaro-7.4.1-2019.02-x86_64_arm-linux-gnueabi/bin/arm-linux-gnueabi-

3. Переходим в work/linux, снова правим arch/arm/boot/dts/imx28-evk.dts

4. Запускаем defconfig:
make ARCH=arm mxs_defconfig

5. Пробуем собрать:
make ARCH=arm CROSS_COMPILE=${ARMCC_GNUEABI7} zImage modules dtbs

Подцепляем ядро к bouldroot
1. В ~/work/buildroot создаем файл local.mk со следующим содержимым:
LINUX_OVERRIDE_SRCDIR = ../linux
Это путь к отдельно лежащему ядру.

2. Правим конфигурацию:
Нажмите, чтобы открыть спойлер

Код:
  │ │[*] Linux Kernel                                                 │ │  
  │ │          *** Linux kernel in thumb mode may be broken with binutils │ │  
  │ │          Kernel version (Custom version)  --->                      │ │  
  │ │    (4.19) Kernel version                                            │ │  
  │ │    ()    Custom kernel patches                                      │ │  
  │ │          Kernel configuration (Using a custom (def)config file)  ---│ │  
  │ │    (kernel.config) Configuration file path                          │ │  
  │ │    ()    Additional configuration fragment files                    │ │  
  │ │    ()    Custom boot logo file path                                 │ │  
  │ │          Kernel binary format (zImage)  --->                        │ │  
  │ │          Kernel compression format (gzip compression)  --->         │ │  
  │ │[*]   Build a Device Tree Blob (DTB)                             │ │  
  │ │    (imx28-evk) In-tree Device Tree Source file names                │ │  
  │ │    ()      Out-of-tree Device Tree Source file paths                │ │  
  │ │    [ ]   Install kernel image to /boot in target                    │ │  
  │ │    [ ]   Needs host OpenSSL                                         │ │  
  │ │    [ ]   Needs host libelf                                          │ │  
  │ │          Linux Kernel Extensions  --->                              │ │  
  │ │          Linux Kernel Tools  --->                                   │ │

3. Копируем linux/.config в buildroot/kernel.config

Пробуем собрать:
.../buildroot$ make linux-rebuild
Здесь у меня была ошибка но уже решили проблема с cp.

Далее записал на sd-карту с помощью dd
запустил и увидал ошибку
Нажмите, чтобы открыть спойлер

Код:
<0>HTLLCLLC

U-Boot 2018.05 (May 28 2019 - 11:53:24 +0700)

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SD/MMC #0, 3V3
SPI:   ready
DRAM:  128 MiB
No arch specific invalidate_icache_all available!
NAND:  256 MiB
MMC:   MXS MMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

Failed (-5)
Video: MXSFB: 'videomode' variable not set!
In:    serial
Out:   serial
Err:   serial
Net:   FEC0 [PRIME], FEC1
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
** Unable to read file boot.scr **
4745472 bytes read in 1405 ms (3.2 MiB/s)
Booting from mmc ...
22034 bytes read in 32 ms (671.9 KiB/s)
Kernel image @ 0x42000000 [ 0x000000 - 0x486900 ]
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 47b18000, end 47b20611 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.19.0 (alexey@alexey) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #2 Tue May 28 14:45:25 +07 2019
[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX28 Evaluation Kit
[    0.000000] Memory policy: Data cache writeback
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x470 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyAMA0,115200 root=/dev/mmcblk0p3 rw rootwait
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 112752K/131072K available (6359K kernel code, 561K rwdata, 2176K rodata, 308K init, 7445K bss, 18320K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (6361 kB)
[    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   ( 308 kB)
[    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 562 kB)
[    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   (7446 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Running RCU self tests
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: mxs_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000038] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.002133] Console: colour dummy device 80x30
[    0.002307] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.002375] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.002433] ... MAX_LOCK_DEPTH:          48
[    0.002485] ... MAX_LOCKDEP_KEYS:        8191
[    0.002538] ... CLASSHASH_SIZE:          4096
[    0.002592] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.002648] ... MAX_LOCKDEP_CHAINS:      65536
[    0.002701] ... CHAINHASH_SIZE:          32768
[    0.002754]  memory used by lock dependency info: 4655 kB
[    0.002808]  per task-struct memory footprint: 1536 bytes
[    0.003125] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[    0.071463] pid_max: default: 32768 minimum: 301
[    0.072677] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.072794] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.080991] CPU: Testing write buffer coherency: ok
[    0.090572] Setting up static identity map for 0x40008400 - 0x40008458
[    0.102055] devtmpfs: initialized
[    0.170348] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.170599] futex hash table entries: 256 (order: 1, 11264 bytes)
[    0.172200] pinctrl core: initialized pinctrl subsystem
[    0.187004] NET: Registered protocol family 16
[    0.189990] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.413906] Serial: AMBA PL011 UART driver
[    0.417850] 80074000.serial: ttyAMA0 at MMIO 0x80074000 (irq = 236, base_baud = 0) is a PL011 rev2
[    0.745079] console [ttyAMA0] enabled
[    0.844396] mxs-dma 80004000.dma-apbh: initialized
[    0.863665] mxs-dma 80024000.dma-apbx: initialized
[    0.894982] SCSI subsystem initialized
[    0.902132] usbcore: registered new interface driver usbfs
[    0.908521] usbcore: registered new interface driver hub
[    0.914841] usbcore: registered new device driver usb
[    0.930794] pps_core: LinuxPPS API ver. 1 registered
[    0.936076] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.945501] PTP clock support registered
[    0.952698] Advanced Linux Sound Architecture Driver Initialized.
[    0.968729] clocksource: Switched to clocksource mxs_timer
[    1.615856] NET: Registered protocol family 2
[    1.625687] tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 5120 bytes)
[    1.633809] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.641178] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    1.648121] TCP: Hash tables configured (established 1024 bind 1024)
[    1.655918] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.662480] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.670487] NET: Registered protocol family 1
[    1.681940] RPC: Registered named UNIX socket transport module.
[    1.688200] RPC: Registered udp transport module.
[    1.693245] RPC: Registered tcp transport module.
[    1.698043] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.720658] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.820081] NFS: Registering the id_resolver key type
[    1.826489] Key type id_resolver registered
[    1.831271] Key type id_legacy registered
[    1.835916] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.869904] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.877710] io scheduler noop registered (default)
[    1.882860] io scheduler mq-deadline registered
[    1.887494] io scheduler kyber registered
[    1.902266] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    1.912945] pwm-backlight backlight: Linked as a consumer to regulator.0
[    1.929978] 8006a000.serial: ttyAPP0 at MMIO 0x8006a000 (irq = 234, base_baud = 1500000) is a 8006a000.serial
[    1.942400] mxs-auart 8006a000.serial: Found APPUART 3.1.0
[    1.950701] 80070000.serial: ttyAPP3 at MMIO 0x80070000 (irq = 235, base_baud = 1500000) is a 80070000.serial
[    1.963224] mxs-auart 80070000.serial: Found APPUART 3.1.0
[    1.974895] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.981869] [drm] No driver support for vblank timestamp query.
[    1.989627] mxsfb 80030000.lcdif: Failed to create outputs
[    2.050202] random: fast init done
[    2.093833] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    2.100492] nand: Micron MT29F2G08ABAEAWP
[    2.104593] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.119894] Scanning device for bad blocks
[    3.398205] gpmi-nand 8000c000.gpmi-nand: driver registered.
[    3.429786] m25p80 spi1.0: unrecognized JEDEC id bytes: ff, ff, ff
[    3.441575] libphy: Fixed MDIO Bus: probed
[    3.458075] fec 800f0000.ethernet: Linked as a consumer to regulator.3
[    3.610478] libphy: fec_enet_mii_bus: probed
[    3.621575] fec 800f4000.ethernet: 800f4000.ethernet supply phy not found, using dummy regulator
[    3.631481] fec 800f4000.ethernet: Linked as a consumer to regulator.0
[    3.645630] usbcore: registered new interface driver asix
[    3.651841] usbcore: registered new interface driver ax88179_178a
[    3.658406] usbcore: registered new interface driver cdc_ether
[    3.665110] usbcore: registered new interface driver smsc95xx
[    3.671639] usbcore: registered new interface driver net1080
[    3.677789] usbcore: registered new interface driver cdc_subset
[    3.684418] usbcore: registered new interface driver zaurus
[    3.690894] usbcore: registered new interface driver cdc_ncm
[    3.696653] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.704040] usbcore: registered new interface driver usb-storage
[    3.717505] imx_usb 80080000.usb: Linked as a consumer to regulator.4
[    3.744314] imx_usb 80090000.usb: Linked as a consumer to regulator.5
[    3.756538] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    3.762819] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    3.799046] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    3.820801] hub 1-0:1.0: USB hub found
[    3.825408] hub 1-0:1.0: 1 port detected
[    3.845856] input: mxs-lradc-ts as /devices/soc0/80000000.apb/80040000.apbx/80050000.lradc/mxs-lradc-ts/input/input0
[    3.867310] stmp3xxx-rtc 80056000.rtc: rtc core: registered 80056000.rtc as rtc0
[    3.877186] i2c /dev entries driver
[    3.892216] stmp3xxx_rtc_wdt stmp3xxx_rtc_wdt: initialized watchdog with heartbeat 19s
[    3.905911] mxs-mmc 80010000.ssp: Linked as a consumer to regulator.2
[    3.944177] mxs-mmc 80010000.ssp: initialized
[    3.971931] mxs-dcp 80028000.dcp: Failed to register sha1 hash!
[    3.981017] mxs-dcp: probe of 80028000.dcp failed with error -22
[    3.997843] mmc0: host does not support reading read-only switch, assuming write-enable
[    4.007802] usbcore: registered new interface driver usbhid
[    4.013710] usbhid: USB HID core driver
[    4.020437] mmc0: new high speed SDHC card at address 0007
[    4.045453] mmcblk0: mmc0:0007 SL16G 14.5 GiB 
[    4.086491] sgtl5000 0-000a: Linked as a consumer to regulator.1
[    4.093329]  mmcblk0: p1 p2 p3
[    4.131697] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[    4.140555] NET: Registered protocol family 17
[    4.146432] Key type dns_resolver registered
[    4.158579] registered taskstats version 1
[    4.249913] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.256852] [drm] No driver support for vblank timestamp query.
[    4.264152] mxsfb 80030000.lcdif: Failed to create outputs
[    4.279144] sgtl5000 0-000a: Error reading chip id -6
[    4.290012] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[    4.301089] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.307810] [drm] No driver support for vblank timestamp query.
[    4.314793] mxsfb 80030000.lcdif: Failed to create outputs
[    4.323312] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[    4.333058] stmp3xxx-rtc 80056000.rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
[    4.343318] usb0_vbus: disabling
[    4.347031] lcd-3v3: disabling
[    4.350443] can-3v3: disabling
[    4.353606] lcd-5v: disabling
[    4.356707] ALSA device list:
[    4.359954]   No soundcards found.
[    4.369186] uart-pl011 80074000.serial: no DMA platform data
[    4.388417] EXT4-fs (mmcblk0p3): mounting ext2 file system using the ext4 subsystem
[    4.432318] EXT4-fs (mmcblk0p3): warning: mounting unchecked fs, running e2fsck is recommended
[    4.480116] EXT4-fs (mmcblk0p3): mounted filesystem without journal. Opts: (null)
[    4.488087] VFS: Mounted root (ext2 filesystem) on device 179:3.
[    4.531310] devtmpfs: mounted
[    4.536936] Freeing unused kernel memory: 308K
[    4.541729] This architecture does not have kernel memory protection.
[    4.548260] Run /sbin/init as init process
[    4.617788] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    4.617788] 
[    4.627033] CPU: 0 PID: 1 Comm: init Not tainted 4.19.0 #2
[    4.632584] Hardware name: Freescale MXS (Device Tree)
[    4.637852] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[    4.645695] [] (show_stack) from [] (panic+0xcc/0x258)
[    4.652660] [] (panic) from [] (do_exit+0x9ec/0xa3c)
[    4.659447] [] (do_exit) from [] (do_group_exit+0x38/0xbc)
[    4.666758] [] (do_group_exit) from [] (get_signal+0x204/0x79c)
[    4.674502] [] (get_signal) from [] (do_signal+0x1dc/0x4b0)
[    4.681907] [] (do_signal) from [] (do_work_pending+0xdc/0x110)
[    4.689651] [] (do_work_pending) from [] (slow_work_pending+0xc/0x20)
[    4.697893] Exception stack(0xc7485fb0 to 0xc7485ff8)
[    4.703016] 5fa0:                                     bec2bf10 00000000 00000000 00000000
[    4.711266] 5fc0: 00000940 00000000 00000000 00000000 00000000 00000000 000275e4 00000000
[    4.719514] 5fe0: 00000000 bec2bf10 b6f2eb53 b6f2f000 00000030 ffffffff
[    4.726247] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    4.726247]  ]---


Почему так не знаю.

Реклама:

Последний раз редактировалось Alex_golubev; 02.06.2019 в 13:02.
Alex_golubev вне форума  
Непрочитано 02.06.2019, 18:51  
mike-y-k
Модератор
 
Регистрация: 04.08.2010
Адрес: Москва СЗАО
Сообщений: 7,901
Сказал спасибо: 8,076
Сказали Спасибо 2,505 раз(а) в 1,921 сообщении(ях)
mike-y-k на пути к лучшему
По умолчанию Re: imx287 ошибка загрузки линукса

Alex_golubev, таки такие длинные файлы сильно оптимальнее с добавлением расширения .txt вставлять через управление вложениями. Тут и объём сообщения великоват и спойлеры не у всех отрабатывают, и потери содержимого вполне возможны…
Для нормального анализа неплохо бы конфигурацию для uboot и для начала листинг /etc со всеми поддиректориями…
__________________
rtfm forever должно быть основой для каждого. Альтернатива грустна, поскольку метод слепого щенка успешно работает при малом числе вариантов…
mike-y-k вне форума  
 

Закладки
Опции темы

Ваши права в разделе
Вы не можете создавать новые темы
Вы не можете отвечать в темах
Вы не можете прикреплять вложения
Вы не можете редактировать свои сообщения

BB коды Вкл.
Смайлы Вкл.
[IMG] код Вкл.
HTML код Выкл.

Быстрый переход

Похожие темы
Тема Автор Раздел Ответов Последнее сообщение
Ускорить компьютер 7Fantomas7 Ремонт оргтехники 111 08.08.2018 05:27
ошибка при чтении списка цепей Витя19 KiCAD 2 10.04.2017 14:35
Книги dosikus Делимся опытом 11243 29.12.2015 23:45
в Canon PC780 после копирования высвечивается ошибка Е007 Anton_uz Ремонт оргтехники 1 16.04.2011 13:03
Кода сбоя загрузки мат. платы AV8 George-sun Ремонт оргтехники 0 27.02.2009 14:07


Часовой пояс GMT +4, время: 19:56.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd. Перевод: zCarot